Australian Shipping Notes
While we do have shipping to Australian it is under the following terms:
- 1. If you order complete light guns Australian has once in the past confiscated one of our light guns. If this happens it is on you ordering something you know may or may not be acceptable in your country and we will not replace it. We ship with generic paperwork and never mention the ‘G’ word, it’s shipped as an arcade controller. If the shipment is returned to us we will reship. I know this condition sucks but this is a uniquely AUS problem and it’s either that or we remove AUS
- We ship kits to AUS with VERY generic contents contained in a CR-90, which is a 3D printed rectangle with some buttons and a camera, this is the best way for us to help your order.
- Australian shipping costs are totally random so we have tacked a ‘max average’ cost onto shipping to cover the variance. After creating the label and calculating the true costs we will refund you the difference.
Ready to Go
Complete ready to go Blamcons, fresh from our paint shop. These are one of a kind creations featuring custom paint, hydro dipping, and even some discounted shop demos.
Features
- Ready to Ship custom Vypers
- Ready to ship custom Auto-9s
- One off and unique creations
Blamcon Core
The Blamcon core is the heart of all Blamcon light guns and Blamcon conversions. This compact universal Light Gun board comes preinstalled with Blamcon and has all the on-board hardware and connections you need to get going quickly and easily into the world of DIY light guns.
Features
- On-board Raspberry Pi Pico W
- On-board electronics for rumble and recoil
- Connections for joystick, buttons, foot pedal, and everything else you need to play light gun games
$60
Blamcon Vyper Parts Kit
The basic parts kit includes what you need to build a Blamcon Vyper EXCEPT the 3D printed parts, cable, stock bars and IR bars.
This is best if you already have a cable and a light gun setup and want to build a Vyper. You can also purchase the IR bars and cable separately.
Includes
Electronic Parts: Blamcon Core, SEN0158 IR Camera, Joystick module, JF Z05 solenoid, N20 Rumble motor, Mini Microswitch – 2, Microswitch, USB Connector, NeoPixel LED, 8mm button x2, GX16 6pin connector
Pan head screws: M2x5 – 4, M3X6 – 4, M3X12 – 4, M4X8 – 4, M4X14 – 4, M4X16 – 4, M4X25
Cap head screws: M3X16, M3X20 | Flat head screws: M3X12 | Button head screws: M4X35 | Grub screws M3X6 – 3, M4X6 – 1 | Square nut: M3 | Washer 4x8x.5
Wire: 1.4M Black wire, .6M Red Wire, 3M White wire, 10.5CM 2 strand solenoid wire
Springs: 4x15x.5mm, 6x25x.4mm, 8x40x.5mm-2 | Brass rod: 4x19mm, 2.5x12mm – 2, 2x12mm – 4
$175
Blamcon Vyper Parts Kit – Deluxe
The basic parts kit includes what you need to build a Blamcon Vyper EXCEPT the 3D printed parts, cable, stock bars and IR bars. The Deluxe Kit includes additional premium parts such as a CNC cut actuator bar, Omron switches, copper bushing for recoil, and pre-cut color coded wire.
This is best if you already have a cable and a light gun setup and want to build a Vyper. You can also purchase the IR bars and cable separately.
Includes
Deluxe Parts: Omron Mini Microswitch, Omron Microswitch, CNC cut metal charging handle actuator, copper bushings, all wires precut and stripped.
Electronic Parts: Blamcon Core, SEN0158 IR Camera, Joystick module, JF Z05 solenoid, N20 Rumble motor, Mini Microswitch – 2, Microswitch, USB Connector, NeoPixel LED, 8mm button x2, GX16 6pin connector
Pan head screws: M2x5 – 4, M3X6 – 4, M3X12 – 4, M4X8 – 4, M4X14 – 4, M4X16 – 4, M4X25
Cap head screws: M3X16, M3X20 | Flat head screws: M3X12 | Button head screws: M4X35 | Grub screws M3X6 – 3, M4X6 – 1 | Square nut: M3 | Washer 4x8x.5
Wire: Black: 22mm, 160mm, 60mm, 410mm, 90mm, 170mm, 75mm | Red: 22mm, 160mm, 60mm, 90mm | Orange: 160mm, 190mm | Yellow 160mm, 60mm, 160mm | Gray 120mm, 380mm | Green 22mm, 160mm, 60mm | Blue 160mm, 380mm | Purple 160mm, 85mm | White 22mm, 90mm
Springs: 4x15x.5mm, 6x25x.4mm, 8x40x.5mm-2 | Brass rod: 4x19mm, 2.5x12mm – 2, 2x12mm – 4
$200
Blamcon Vyper 3D Prints
Complete 3D printed parts for the Blamcon Vyper.
Printed out of Matter 3D Performance PLA at .16 layer height, 5shells and 7 top and bottom layers these prints give heft and can take a beating.
Please specify what color you would like for the 3D prints in the notes: Red, Blue, Green, Yellow, Orange, Purple, Pink
$105
Blamcon Vyper Complete Build Kit
Blamcon Vyper Complete Build Kit includes what you need to build a Blamcon Vyper EXCEPT the 3D printed parts.
Includes
GX16 Cable with 12V 3A Adapter
Light Bar Kit
Electronic Parts: Blamcon Core, SEN0158 IR Camera, Joystick module, JF Z05 solenoid, N20 Rumble motor, Mini Microswitch – 2, Microswitch, USB Connector, NeoPixel LED, 8mm button x2, GX16 6pin connector
Pan head screws: M2x5 – 4, M3X6 – 4, M3X12 – 4, M4X8 – 4, M4X14 – 4, M4X16 – 4, M4X25
Cap head screws: M3X16, M3X20 | Flat head screws: M3X12 | Button head screws: M4X35 | Grub screws M3X6 – 3, M4X6 – 1 | Square nut: M3 | Washer 4x8x.5
Wire: 1.4M Black wire, .6M Red Wire, 3M White wire, 10.5CM 2 strand solenoid wire
Springs: 4x15x.5mm, 6x25x.4mm, 8x40x.5mm-2 | Brass rod: 4x19mm, 2.5x12mm – 2, 2x12mm – 4
$200
Blamcon Vyper Complete Build Kit – Deluxe
The Blamcon Vyper Deluxe Parts Kit has everything you need to get up and playing with Blamcon, EXCEPT the 3D printed parts. The Deluxe Kit includes additional premium parts such as a CNC cut actuator bar, Omron switches, copper bushing for recoil, and pre-cut color coded wire.
Includes
GX16 Cable with 12V 3A Adapter
Light Bar Kit
Deluxe Parts: Omron Mini Microswitch – 2, Omron Microswitch, CNC cut metal charging handle actuator, copper bushings for pull to reload – 2, all wires precut and stripped by my wife.
Electronic Parts: Blamcon Core, SEN0158 IR Camera, Joystick module, JF Z05 solenoid, N20 Rumble motor, USB Connector, NeoPixel LED, 8mm button x2, GX16 6pin connector
Pan head screws: M2x5 – 4, M3X6 – 4, M3X12 – 4, M4X8 – 4, M4X14 – 4, M4X16 – 4, M4X25
Cap head screws: M3X16, M3X20 | Flat head screws: M3X12 | Button head screws: M4X35 | Grub screws M3X6 – 3, M4X6 – 1 | Square nut: M3 | Washer 4x8x.5
Wire: Black: 22mm, 160mm, 60mm, 410mm, 90mm, 170mm, 75mm | Red: 22mm, 160mm, 60mm, 90mm | Orange: 160mm, 190mm | Yellow 160mm, 60mm, 160mm | Gray 120mm, 380mm | Green 22mm, 160mm, 60mm | Blue 160mm, 380mm | Purple 160mm, 85mm | White 22mm, 90mm
Springs: 4x15x.5mm, 6x25x.4mm, 8x40x.5mm-2 | Brass rod: 4x19mm, 2.5x12mm – 2, 2x12mm – 4
$230
Blamcon Vyper – Complete
Complete Blamcon Vyper. Hand made and balanced by Chris and Mike.
Colors available: Red, Blue, Green, Orange, Yellow, Purple Pink.
They come with an orange barrel as per law, we can ‘leave’ a color of your choice in the box, after you get it its yours.
Incudes
- Blamcon Vyper
- Locking GX 16 Cable (USB / 12V at one end, GX16-6 at the other)
- 12V 3A Adapter
- 2 Blamcon light bars (USB powered) OR Presoldered Blamcon arcade LEDs (let us know which way you want to go)
- Blamcon Manual
$500
Blamcon Vyper – Complete – Paint and Hydrodipped
Complete Blamcon Vyper, painted and Hydrodipped by Mike. Hand made and Balanced by Chris and Mike. See our gallery of completed Hydrodips for inspiration but we’re always about doing something custom for you.
Incudes
- Blamcon Vyper
- Locking GX 16 Cable (USB / 12V at one end, GX16-6 at the other)
- 12V 3A Adapter
- 2 Blamcon light bars (USB powered) OR Presoldered Blamcon arcade LEDs (let us know which way you want to go)
- Blamcon Manual
They come with an orange barrel as per law. If you want another color of barrel in the box, let us know.
$650
Blamcon GX16 Cable + Adapter
The Blamcon GX16 cable has everything you need to get going with your new Blamcon or any GX16 6 pin light gun. The breakout box has a standard USB connection on one end with a 5.5mmx2.1mm barrel jack and a GX16-6 female connector on the other end. Comes with a 12V 3A adapter.
Pinout:
- 12V Positive
- 12V Negative
- USB Positive
- USB Data +
- USB Data –
- USB Negative
$30~$40
Blamcon IR Bar Set, Ready To Go | Up to 85” TV
Complete and ready to go Blamcon Light Bar set to mount to the top and bottom of your TV or monitor.
If you are using a Blamcon, the bars are by far the best way to go. They will give you the best play area and are the easiest to mount properly. bars are easy to center and are the cleanest way to set up your IR emitters.
To learn more visit https://blamcon.com/blamcon-irbar/
Includes:
-
- 2 Blamcon Bars connected to one 1M USB Power Cable
- 130 CM cable connecting the bars, more than enough for an 85″ or under TV
- Alien Tape mounts, one flat and one adjustable, to connect to your TV.
$55
Blamcon IR 4 Module Set, Ready To Go | Up to 85” TV
Complete and ready to go Blamcon Light Emitter set to mount to your TV in edge or 4 corner configuration.
4 Corner: 2 banks of LEDs on top and bottom edge of TV
4 corners Pattern is for third party compatibility. Single sensors also allow you to move them around if you want multiple 3rd party support. using this config gives you less lateral play area so we recommend moving these to blamcon bar spacing, 250mm, if you do. The build guide for this starts AFTER the bars section.
Crosshair: One LED bank on each edge of your TV
Crosshair pattern is for compatibility with third party systems and is the hardest to mount. We do not recommend using this config only for Blamcon. Make sure you change your IR settings to crosshair in the free Blamcon ARC utility on steam.
To learn more visit https://blamcon.com/blamcon-irbar/
Includes:
-
- 2 Blamcon Bars connected to one 1M USB Power Cable
- 130 CM cable connecting the bars, more than enough for an 85″ or under TV
- Alien Tape mounts, one flat and one adjustable, to connect to your TV.
$60
Blamcon IR Mega Bar Set, Ready To Go | Up to 150” TV
Complete and ready to go Blamcon Light Mega Bar set to mount to the top and bottom of your TV or monitor.
If you are using a Blamcon, the bars are by far the best way to go. They will give you the best play area and are the easiest to mount properly. bars are easy to center and are the cleanest way to set up your IR emitters.
To learn more visit https://blamcon.com/blamcon-irbar/
Includes:
-
- 2 Blamcon Mega Bars connected to one 1M USB Power Cable
- 5M cable connecting the bars, more than enough for an 85″ or under TV
- Alien Tape mounts, one flat and one adjustable, to connect to your TV.
$65
Blamcon IR Bar Kit | Up to 85” TV / Arcade Machine
Blamcon Light Bar kit to mount to your TV or Arcade Machine. Note you will have to 3D print the light bar files yourself, download them at: https://blamcon.com/blamcon-irbar/
No 3D printing required for arcade machines.
If you are using a Blamcon, the bars are by far the best way to go. They will give you the best play area and are the easiest to mount properly. bars are easy to center and are the cleanest way to set up your IR emitters.
To learn more visit https://blamcon.com/blamcon-irbar/
Includes:
-
- 4 Blamcon Emitters with 3 Osram SFH4547 IR LEDs in Each
- 3M 28ga Wire
- 1M LED Power Cable
- Pan Head Screws – M3x10mm X 12
- Pan Head Screws – M3x12mm X 4
- Cap Head Screws – M3x16mm X 4
$40
Blamcon IR 4 Module Kit | Up to 85” TV / Arcade Machine
Blamcon IR Module kit to mount to your TV in edge or 4 corner configuration. This kit will also work in an arcade machine
4 Corner: 2 banks of LEDs on top and bottom edge of TV
4 corners Pattern is for third party compatibility. Single sensors also allow you to move them around if you want multiple 3rd party support. using this config gives you less lateral play area so we recommend moving these to blamcon bar spacing, 250mm, if you do. The build guide for this starts AFTER the bars section.
Crosshair: One LED bank on each edge of your TV
Crosshair pattern is for compatibility with third party systems and is the hardest to mount. We do not recommend using this config only for Blamcon. Make sure you change your IR settings to crosshair in the free Blamcon ARC utility on steam.
To learn more visit https://blamcon.com/blamcon-irbar/
Includes:
-
- 4 Blamcon Emitters with 3 Osram SFH4547 IR LEDs in Each
- 6.5M 28ga Wire
- 1M LED Power Cable
- Pan Head Screws – M3x10mm X 8
- Pan Head Screws – M3x12mm X 8
- Cap Head Screws – M3x16mm X 8
$45
Blamcon IR Mega Bar Kit | Up to 150” TV / Arcade Machine
Blamcon Mega Light Bar kit to mount to your TV or Arcade Machine. Note you will have to 3D print the light bar files yourself, download them at: https://blamcon.com/blamcon-irbar/
No 3D printing required for arcade machines.
If you are using a Blamcon, the bars are by far the best way to go. They will give you the best play area and are the easiest to mount properly. bars are easy to center and are the cleanest way to set up your IR emitters.
To learn more visit https://blamcon.com/blamcon-irbar/
Includes:
-
- 4 Blamcon Emitters with 3 Osram SFH4547 IR LEDs in Each
- 8M 28ga Wire
- 1M LED Power Cable
- Pan Head M3x10mm X 12
- Pan Head M3x12mm X 8
- Pan Head M3x16mm X4
- Cap Head M3x20mm X 4
$50
Blamcon Auto 9 | Blamcon Auto 9 Light Gun | Complete Parts Kit with 3D Prints
The Blamcon Auto 9 is a PC compatible light gun you build yourself. Features slide recoil, rumble, RGB LED, 2 buttons, and a competition trigger.
See https://blamcon.com/blamcon-auto-9/ for more information.
Blamcon Auto9 Complete Build Kit includes everything you need to build a Blamcon Auto 9 INCLUDING black 3D printed parts.
Includes
Blamcon Auto 9 3D Prints printed from Matter3D Performance PLA (made in Canada) at .16
GX16 Cable with 12V 3A Adapter
Light Bar Kit
Electronic Parts: Blamcon Core, SEN0158 IR Camera, JF-0826B 12V solenoid, N20 Rumble motor, Mini Microswitch, USB Connector, NeoPixel LED, 8mm button x2, GX16 6pin connector
Pan head screws: M2x5 – 4, M3X6 – 4, M3X12 – 4, M4X8 – 4, M4X14 – 4, M4X16 – 4, M4X25
Cap head screws: M3X16, M3X20 | Flat head screws: M3X12 | Button head screws: M4X35 | Grub screws M3X6 – 3, M4X6 – 1 | Square nut: M3 | Washer 4x8x.5
Wire: 1.4M Black wire, .6M Red Wire, 3M White wire, 14CM 2 strand solenoid wire
Springs: 4x15x.5mm
Brass rod: 4x19mm, 2.5x12mm – 2
$225
Blamcon Auto 9 | Build Kits
Blamcon Auto9 Complete Build Kit includes what you need to build a Blamcon Auto 9 EXCEPT the 3D printed parts.
Includes
Light Bar Kit (optional)
GX16 Cable with 12V 3A Adapter (optional)
Electronic Parts: Blamcon Core, SEN0158 IR Camera, JF-0826B 12V solenoid, N20 Rumble motor, Mini Microswitch, USB Connector, NeoPixel LED, 8mm button x2, GX16 6pin connector
Pan head screws: M2x5 – 4, M3X6 – 4, M3X12 – 4, M4X8 – 4, M4X14 – 4, M4X16 – 4, M4X25
Cap head screws: M3X16, M3X20 | Flat head screws: M3X12 | Button head screws: M4X35 | Grub screws M3X6 – 3, M4X6 – 1 | Square nut: M3 | Washer 4x8x.5
Wire: 1.4M Black wire, .6M Red Wire, 3M White wire, 14CM 2 strand solenoid wire
Springs: 4x15x.5mm
Brass rod: 4x19mm, 2.5x12mm – 2
$170
Blamcon Auto 9 Light Gun | 3D Prints
The Blamcon Auto 9 is a PC compatible light gun you build yourself. Features slide recoil, rumble, RGB LED, 2 buttons, and a competition trigger.
See https://blamcon.com/blamcon-auto-9/ for more information.
Includes
– Blamcon Auto 9 3D Prints printed from Matter3D Performance PLA (made in Canada) at .16.
– Black Lens adapter and optional Orange Barrel shroud Lens Adapter.
$50
Blamcon Buddy | One Handed Controller Kit
The Blamcon Buddy is the bestest of pals for any one handed Blamcon. It lets you assign up to 5 buttons to use with your off hand. No more holding pistols awkwardly with 2 hands while you play just so you can hit that grenade button, use your grenade hand like the universe intended!
Features:
- Wireless, binds directly to your Blamcon
- 4 Cherry MX Finger Keys with a CNC aluminum mounting plate
- Metal thumb button on top
- Feedback LED
- Rechargeable via USB-C
- Real leather hand strap (alternatives available upon request)
Incudes
Everything EXCEPT 3D Printed Parts
Electronic Parts: Pico W Microcontroller | Micro USB Connector | 3.7v 550ma lipo Battery | TP4057 Charging Module | USB C Port | Neopixel LED | 10mm LED Diffuser (Printable) | 10×15 Toggle Switch | Cherry MX Key (Silver) X 4 | Black Keycap X 4 | 16mm Metal Push Button | CNC Metal Mounting Plate | Leather Strap (19mmX210mm)
Flat head screws: M4x12 X 4
Pan head screws: M2x5 X 4 | M4x10 X 2
Wire 28ga (cut and stripped): Black 35mm, Black 35mm,Black 140mm,Black 30mm, Red 35mm, Red 35mm, Red 140mm, Red 30mm, Yellow mm, Green 30mm, Green 55mm, Blue 55mm, Brown 60mm, Gray 55mm, White 30mm, White 30mm, Extra Wire 300mm
$60
Blamcon Buddy | One Handed Controller
The Blamcon Buddy is the bestest of pals for any one handed Blamcon. It lets you assign up to 5 buttons to use with your off hand. No more holding pistols awkwardly with 2 hands while you play just so you can hit that grenade button, use your grenade hand like the universe intended!
Features:
- Wireless, binds directly to your Blamcon
- 4 Cherry MX Finger Keys with a CNC aluminum mounting plate
- Metal thumb button on top
- Feedback LED
- Rechargeable via USB-C
- Real leather hand strap (alternatives available upon request)
Incudes
- Blamcon Buddy
- USB C-Cable
Note: Let us know if you’re left handed (which would mean you’re holding the Buddy in your right hand)
$80
Blamcon Buddy | One Handed Controller | Custom Paints and Dips
The Blamcon Buddy is the bestest of pals for any one handed Blamcon. It lets you assign up to 5 buttons to use with your off hand. No more holding pistols awkwardly with 2 hands while you play just so you can hit that grenade button, use your grenade hand like the universe intended!
Features:
- Wireless, binds directly to your Blamcon
- 4 Cherry MX Finger Keys with a CNC aluminum mounting plate
- Metal thumb button on top
- Feedback LED
- Rechargeable via USB-C
- Real leather hand strap (alternatives available upon request)
Incudes
- Blamcon Buddy
- USB C-Cable
Note: Let us know if you’re left handed (which would mean you’re holding the Buddy in your right hand)